Back Pressure Shearbox - High Pressure

An axial compression test determines the behaviour of geo-materials when the major load is applied in the axial direction. The specimen load and displacement is recorded while the specimen is compressed. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Enables a direct shear test in which the load is cycled back and forth to be performed on a specimen at dynamic rates with back pressure applied. 

Enables a direct shear test in which the load is cycled back and forth to be performed on a specimen at static rates with back pressure applied.

Enables a direct shear test to be performed on a specimen at static rates with back pressure applied.

Some geotechnical applications require the continuous flow of fluid, either under pressure control or via a rate of fluid flow.  GDS manufacture an Infinite Volume Controller (IVC). By connecting 2 GDS pressure/volume controllers in parallel, the IVC system automatically switches between them when they run out of volume thus providing a seamless supply of pressure with unlimited volume capacity.  The IVC can be used with any 2 pressure controllers from the GDS range, i.e. advanced, standard or enterprise. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Slow cyclic testing may be performed on all GDS triaxial testing apparatus with the appropriate software modules.  The speed the cycles can be applied is determined by the performance of the system.  A standard load frame generally only used for quasi-static testing can perform cyclic testing with periods of around 5 minutes when coupled with GDSLAB control and data acquisition software. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Cyclic loading refers to the repeated loading of a sample.  All GDS systems can imply this loading either under load control, or under strain (displacement) control.  Load control will be via feedback from the load cell and displacement control will be via the feedback from the displacement transducer.  Load and displacement control can be performed by all GDS system.  The speed of the cyclic loading depends on the frequency performance (i.e. the dynamic performance) of the system in question.  Dynamic stress control is possible, but only available on the most advanced GDS dynamic because of the additional processing required to calculate the sample area during the cycles.  Please note: Some apparatus may require additional components or software modules to perform certain tests.

Direct shear tests: The sample is contained inside a rigid box with a horizontal split line at the mid-height of the sample. The shear force is applied to the sample by moving the two halves of the box horizontally relative to each other. The intension is to induce a shear plane to form between the two halves of the sample. Properties can be obtained for the material prior to shear and post failure or residual. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Direct shear testing of a geo-synthetic material embedded in a soil specimen to determine the shear strength of the geo-synthetic-soil system. 

Kzero conditions (or specifically the coefficient of earth pressure at rest) in the context of laboratory testing are where a sample is required to be loaded whilst keeping the area of the sample a constant.  Kzero conditions are maintained in a n oedometer by design due to the radial constraint, however in an oedometer the radial stress cannot be measured therefore the K-zero condition is not measureable.  A Kzero test in a triaxial cell allows Kzero conditions to be applied and measured. The Kzero module allows you to run two tests. 

• Test 1: Kzero using ramp RADIAL STRESS with direct radial transducer measurement: Uses a direct reading of the specimen diameter to enable the test control to maintain zero diameter change.
  
• Test 2: Kzero using ramp RADIAL STRESS with back volume change measurement: Uses the change in volume of the specimen to calculate a theoretical new specimen height thus ensuring the diameter change remains zero.
  

Please note: Some apparatus may require additional components or software modules to perform certain tests.

Enables application of load to a specimen for tens of seconds or more, and at frequencies less than 0.1 Hz during cyclic loading. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Determination of the maximum (i.e., very small strain) shear modulus of a specimen. Please note: Some apparatus may require additional components or software modules to perform certain tests.

The procedure for conventional triaxial tests requires three separate soil specimens to be sheared to failure under different confining pressures so that Mohr-Coulomb failure envelope can be determined and soil shear strength parameters can be obtained. An alternative procedure is the multi-stage triaxial compression test, which requires only one soil specimen to be tested at three stages of shearing with different confining pressures.

Uses a datalogger to take settlement readings from a hanging weight oedometer system.  Alternatively, GDS produces an automated oedometer which completely automates one dimensional consolidation testing.

Soil testing involves the application of pressure (stress) and the resulting measurement of strain either by measuring displacements or volume change. GDS pressure/volume controllers can apply pressure and measure volume change, or alternatively can apply volume change and measure the resulting pressure. Essential for soil testing.  Please note: Some apparatus may require additional components or software modules to perform certain tests.

Quasi-static refers to slow speed tests.  Creep tests require accurate displacements to be measurable whilst a continuous, sometimes long term loading is accurately applied. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Saturation ramp allows you to independently increase or decrease the Cell Pressure and the Back Pressure. The saturation ramp is used to steadily change the pressures in the system either keeping a constant effective stress or change to a desired effective stress.

A static displacement test involves applying and maintaining a constant displacement to the specimen. The load response can subsequently be observed. Alternatively this may refer to cases where a displacement, which may vary, is applied to a specimen for tens of seconds or more. Please note: Some apparatus may require additional components or software modules to perform certain tests

A static load test involves applying and maintaining a constant load on the specimen. The displacement response can subsequently be observed. Alternatively this may refer to cases where a load, which may vary, is applied to a specimen for tens of seconds or more. Please note: Some apparatus may require additional components or software modules to perform certain tests.

Stepped Loading provides a means to increase the specimen axial load, whilst maintaining a constant back pressure and measuring the back (pore) volume change. Please note: Some apparatus may require additional components or software modules to perform certain tests.